- #Backup camera for bmw 3 series install
- #Backup camera for bmw 3 series drivers
- #Backup camera for bmw 3 series driver
- #Backup camera for bmw 3 series manual
The OEM camera works the same as if it was factory installed. Once they contacted me, the programmer took over and programmed my car.
#Backup camera for bmw 3 series install
The software took about 20 minutes to download and install and then I contacted Bimmer-tech to connect. Requires a Windows PC and Internet connection where your car is located. I then contacted Bimmer-tech and received an email advising me of software to pre-install so they can connect to my car. I completed mounting the camera module under the dash (perfect fit) and then returned the iDrive back to the dash and I reinstalled the dash trim. It was a tight fit and the plastic push tool helped. All I had to do was push the pin into the empty slot. The rear fusebox came with the 5A fuse already installed in the empty fuse port already designed for the camera module. The +12V wire was run along the floor, next to the camera cable until I reached the rear fusebox located in the trunk floor. Here I used a supplied OEM tap to connect the camera GND to the lamp GND.
#Backup camera for bmw 3 series drivers
GND was a short run that ran behind the carpet to the drivers side underdash lamp.
#Backup camera for bmw 3 series manual
Not terribly difficult since the manual described the correct wire colors and those were easy to find in the seat harness.
#Backup camera for bmw 3 series driver
These wires are tapped using the supplied OEM wire taps and the wires are located along the driver’s floor, in a harness that runs to the driver seat. The next two wires went to the communication protocol that allows modules to talk with each other. Fairly easy once I removed the iDrive unit.
All 3 wires came with the appropriate pins so all I had to do was push them into the corresponding holes in the main iDrive connector. Next, was to run the main harness which starts under the drivers dash (and attaches to the camera module). Finally got it after 30 minutes of fiddling.įrom there I ran the camera cable starting at the trunk handle hole, through the trunk to the underdash area on driver’s side.
The trouble is the clips are tight and the space for your hands is small.
The trunk release handle is held in place with pressure clips. The biggest pain was to remove the OEM trunk release handle. Took about 2.5 hours to remove all trim pieces (and about 1 hour to reinstall later). IDrive Navigation unit (Nav did not need to be fully removed, just enough to expose the main harness). The retrofit required I remove the following interior parts from car: Definitely be sure to get trim removal tools! #2 Philips screwdriver, torx driver with 3 bit sizes, 10mm socket wrench, wire cutters (to trim the wire ties), a plastic poking tool (to help insert the pins into the factory harnesses), and a set of plastic trim removal tools. First thing was to follow the advice from Patryk (and the manual) and make certain sure I had the following tools: OEM wire taps for 3 of the wires (yes, BMW makes wire taps for repair purposes)Īfter reading through the manual, and a couple clarification emails with Bimmer-tech, I felt I was ready to tackle this project. ODBII cable with RJ45 on other end to connect to computer for programming OEM trunk handle with OEM camera pre-installed OEM camera module (and OEM mounting screw) And for the most part, it was!įirst, for an easy install and proper compatibility, you’ll need the following two options:Ģ) Park Distance Control (rear only is OK)Ī week later a box arrived via DHL containing the following items: After some emailing with Patryk Bimmer-tech, he confirmed my options would make this a relatively painless install. So, after some research I found Bimmer-tech and was pleased to see they offered an OEM retrofit kit for the backup camera. Initially I thought the backup cam wasn’t important, but after a couple months of ownership, I began to have too many occasions where I said to myself, why didn’t I get it…. The 2013 car I purchased came with PDC and Navigation but did not have a backup cam.